VintageKustom.com - RDF feed
http://www.vintagekustom.com/FUDforum/index.php
Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27089&th=4666#msg_27089
I have the schematics for each board and have been probing the PC900 output board for voltages and everything is close. I see no obvious burned components or bad solder joints. I do see -38v on Q2 BLU which is the base of the 36892. Would this be normal? Schematic shows -.1
I removed both Q1 and Q2 tested them Q2 was hFE=35 Vf=526mV Q1 was hFE=25 Vf=517mV
I put them back in swapping positions and Q2 BLU voltage remained -38v.
If you haven't figured it out yet my skill level is beginner/intermediate. I have built a couple pedals from scratch and in the past built a pirate FM radio station. I know enough to most likely not electrocute myself, no promises though.
Any and all help would be appreciated.
Thanks,
Robert/Muddy]]>muddy udders2018-11-07T05:48:16-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27090&th=4666#msg_27090
I would next check the two 5 watt 1 ohm resistors to see if they are open as these just can go open yet not burn.]]>stevem2018-11-07T11:03:46-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27091&th=4666#msg_27091
Have you tested all of the dc voltages from the power supplies?
I'd want to test your theory about the problem being in the power amp before you do too much work here. All of the preamps are of equal loudness, but they all go through the reverb/mixer board, so the problem could be there as well.
Feed a signal into the power amp at the monitor point. I don't remember if the Casino has a jack there or not, but in any case, there is a point on the pc board. See if you can drive the power amp to a higher loudness level than you are getting from the preamps.
If you don't have a signal generator or some sort of phone app, you can use the signal from another amp or a guitar with a boost pedal of some sort, or even an MP3 player.]]>chicagobill2018-11-07T18:04:45-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27092&th=4666#msg_27092
The PA has monitor and tape inputs. I used my phone through both and the sound was clear and louder. When I put it through the front input jacks, I tried them all, the sound was lower and very distorted. Does this mean my issue is on the reverb board?
]]>muddy udders2018-11-07T19:39:46-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27093&th=4666#msg_27093
I hooked up my cell phone to the Monitor jack on the back and the audio was real clear and seemed louder.
I connected through the front inputs and it was quite distorted and not as loud.
The DC voltages on the PC900 board were correct for 8v and 39v. I forgot to check the reverb board voltages.
Does this confirm your theory Chicagobill?]]>muddy udders2018-11-08T01:03:52-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27094&th=4666#msg_27094
stevem2018-11-08T11:02:20-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27095&th=4666#msg_27095
muddy udders wrote on Wed, 07 November 2018 19:03
The DC voltages on the PC900 board were correct for 8v and 39v. I forgot to check the reverb board voltages.
Does this confirm your theory Chicagobill?
Yes, it seems that the power amp is working correctly and the problem is either the reverb board or the low voltage power supply. I don't think that all four preamps would fail at the same time in the same way, unless something unusual happened or was done to the amp.]]>chicagobill2018-11-08T18:09:06-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27096&th=4666#msg_27096
I ordered parts and I will recap the reverb board and see what I get. Where does everyone source parts? I have been using Mammoth, Mouser and circuit specialists even amazon for some stuff. Just looking for vendors.
Thanks for all the help so far i will post up what o find.
Robert/Muddy]]>muddy udders2018-11-08T20:49:08-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27097&th=4666#msg_27097
muddy udders2018-11-09T17:53:29-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27098&th=4666#msg_27098
Any thoughts?]]>muddy udders2018-11-10T04:12:50-00:00Re: Need help troubleshooting a Kasino U100-P
http://www.vintagekustom.com/FUDforum/index.phpindex.php?t=rview&goto=27099&th=4666#msg_27099
What impeadance is the 4-12 cabinet?
The amp wants a 8 ohm load to output its full clean 50 watts of RMS audio output.
If your 4-12 cab is 4 or 16 ohms then you will only have 25 watts of clean output to work with.
You should be seing some 18 to 20 volts of unclipped audio output at the amps speaker output into a 8 ohm test resistor / speaker load if all is well!]]>stevem2018-11-10T11:21:38-00:00