VintageKustom.com: Replacement Part Suggestions

Home » VintageKustom.com » Replacement Part Suggestions » New Lamp for a K50-2

Show: Today's Messages :: Polls :: Message Navigator

New Lamp for a K50-2 [message #5671]

Tue, 05 April 2005 16:35

srandallf
Messages: 13
Registered: April 2005

Junior Member

Hello. does anyone know what lamp to use on a K50-2.

Also, can anyone tell me anything about this model? I just got it. Its in mint condition. It looks like it was never used. I paid alot for it on ebay though, but I think its worth it. I dont care much for the sound of the reverb. Its very tinny sounding and is producing a strange but muted sound that is not normal. Otherwise, I love it. Great tone and has an original C12N I believe. The seller on Ebay said it is soo loud that it "shakes the walls"...well, it is hardly loud enough to rattle my picture frames but I still like it alot. Any info would be appreciated, especially about the lamp..i tried the lamp from my deluxe reverb and it blew immediately...

Thanks

Report message to a moderator

Re: New Lamp for a K50-2 [message #5683 is a reply to message #5671]

Wed, 06 April 2005 08:29

stevem
Messages: 4746
Registered: June 2004
Location: NY

Senior Member

The bulb from your fender is a 6.3 volt bulb. The kustoms run at a higher voltage. I forget the bulb number you need, but I will let you know.The bulb you now need for your fender is a # 47, that you can get from the ampwares site. I think the kustoms number is 49, I am just not sure right now.

Report message to a moderator

Re: New Lamp for a K50-2 - replacement lamp chart [message #5690 is a reply to message #5683]

Thu, 07 April 2005 13:07

LesS
Messages: 477
Registered: December 2002

Senior Member

Hi srandallf,

The bulb you need is an 1829.
Here is more info on replacement bulbs for Kustoms:
...............................................
Replacement pilot lights
VintageKustomFAQ3

Model............................................lamp#....... ..................Volts/ma
K100, K200,Frankie,Combo organ ....1829 (Grainger #6VF92) 28 volts 70ma
(#1819 is 28 volts 40ma and will work but is not as bright as #1829)
Do not use a 6.3 volt bulb, it will make the resistor run too hot.

The output of the transformer is 42 volts - a 200 ohm resistor is wired in series with the bulb that reduces the voltage down to 28 volts.

Model....................................................... .......................... .lamp# .....Volts/ma
K150/K250/Hustler,Sidewinder,Charger,Commander,Challenger . ..GE335 28 volts at 40ma
These two bulbs are not correct and can cause the resistor to overheat:
Radio Shack 272-1143 (12 volts at 75ma)
GE373 (14 volts at 80 ma)

Sources for bulbs:

www.Jameco.com
California
1-800-455-6119
#335 lamp - part # 209605CA - $.59 each

www.mouser.com
Texas
1-800-346-6873
#335 lamp - part # 606-CM335 -$.98 each
#1829 lamp - part # 606-CM1829 -$.74 each ($.64 each for 10 or more)

For Grainger store near you go to www.grainger.com (must have business account to order online)
#1829 lamp - Grainger part # 6VF92

www.ampwares.com

www.magicparts.com

Radio Shack carries only the #1819 bulb (not as bright as #1829)...their number is 272-1119 and it sells for $1.79.

[Updated on: Sun, 30 December 2007 17:34]

Report message to a moderator