Home » VintageKustom.com » Comment Board » Jensen T&R 4x10 cab from 1990’s -sealed or ported?

Show: Today's Messages :: Show Polls :: Message Navigator

Jensen T&R 4x10 cab from 1990’s -sealed or ported? [message #10741] Mon, 13 April 2009 11:39   LesS Messages: 477 Registered: December 2002 Senior Member Hey Steve or anybody, Steve – I know that you have or used to have one of the 4x10 Jensen T&R cabinets from the 1990’s made in China. Was the 4x10 cabinet sealed? – or did it have ports? I just bought four of the 50w Jensen tens and I am going to make a 4x10 baffle and put them in a Kustom 2x15 cabinet. Thanks, Les S. Report message to a moderator

Re: Jensen T&R 4x10 cab from 1990’s -sealed or ported? [message #10742 is a reply to message #10741] Mon, 13 April 2009 18:03   pleat Messages: 1452 Registered: June 2004 Location: Belding, Mi Senior Member Les, I didn't know the new chinese made Kustom T&R offered a 4x10 cabinet. I had two of the 4x12 cabinets in red and they were a sealed cabinet. No ports front or rear. Pleat Report message to a moderator

Re: Jensen T&R 4x10 cab from 1990’s -sealed or ported? [message #10748 is a reply to message #10741] Tue, 14 April 2009 06:06   stevem Messages: 4733 Registered: June 2004 Location: NY Senior Member Its a sealed cab Less which surprised me,as I though that it would be made with a vent slot on the bottom, but just covered with the grill cloth. Report message to a moderator

Re: Jensen T&R 4x10 cab from 1990’s -sealed or ported? [message #10749 is a reply to message #10741] Tue, 14 April 2009 06:13   stevem Messages: 4733 Registered: June 2004 Location: NY Senior Member I see the new Kustom deepend 4-10 cabs are the same, no ports and the cab looks to be the same size pretty much as mine. They look like they use a Eminence driver though. Report message to a moderator

Re: Jensen T&R 4x10 cab from 1990’s -sealed or ported? [message #10756 is a reply to message #10741] Tue, 14 April 2009 09:16   pleat Messages: 1452 Registered: June 2004 Location: Belding, Mi Senior Member I did take some photo's of the Chinese made 4x12 cabinets I had, just to show how cheap they were, 1/2 inch thick particle board construction. It sure would be great if there were an easy way to post photo's on this site. That would open up a of informational value to pass on to everyone. pleat Report message to a moderator

Re: Jensen T&R 4x10 cab from 1990’s -sealed or ported? [message #10757 is a reply to message #10741] Tue, 14 April 2009 09:35   stevem Messages: 4733 Registered: June 2004 Location: NY Senior Member I have one of those 4-12 and a 2-15 cab also besides the 4-10 and its scary how they are just hot glued together, so I made some 90 degree pine angle strips and carpenter glued them in all 4 connors and around the front baffle on all of my cabinets. Report message to a moderator

Previous Topic:	first 4-10 cabinet
Next Topic:	Kustom 605

Goto Forum:

- VintageKustom.com  Comment Board  Replacement Part Suggestions  Repairing Kustom Amps- Classified Ads  For Sale  Wanted- FUDforum Questions & Problems  Questions & Problems about FUDforum