Home » VintageKustom.com » Replacement Part Suggestions » Schematics needed (anyone have some schematics they could Email me)
Schematics needed [message #11733] Wed, 02 September 2009 19:44 Go to next message
cassent5150 is currently offline  cassent5150
Messages: 341
Registered: August 2009
Senior Member
I'm in need of some schematics for a K-100 PA, K-200 PA, K-150-2, Kasino U100 PA, and Kasino 250-bass can anyone help? Thanks STEVE My Email address is cassent5150@hotmail.com

Steve C

[Updated on: Wed, 02 September 2009 20:47]

Report message to a moderator

Re: Schematics needed [message #11735 is a reply to message #11733] Thu, 03 September 2009 05:43 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4250
Registered: June 2004
Location: NY
Senior Member
So you have all of these you need to repair?
Re: Schematics needed [message #11740 is a reply to message #11735] Thu, 03 September 2009 19:47 Go to previous messageGo to next message
cassent5150 is currently offline  cassent5150
Messages: 341
Registered: August 2009
Senior Member
lets see now, I've got 3 K-150-2's and 2 are fine other then the selectone switch issue thats common on all 3, but one of them channel 2 is out as well as the tremolo/vibrato is not oscilating. I have 3 K-200-5's one is fine, one has only a faint sound getting threw on all 4 channels and one has channels 1 and 2 working, but (3 and 4) just a faint sound getting threw. I have a Kasino 250 bass with a clipping problem when the volume is turned up past like 3 " this cold be my own fault, cause I replaced the KEI-1 009-5065-00 PC board with a 5065 out of a K-XII SRS tri amp. 2 Kustom XII-SRS Tri-amps, one is for parts. I've got a K-200-6 that works fine, a K-III 6 channel PA that works fine, one K-100-1 works fine, a Kasino U-100-P 4 channel head that has no signal getting to the driver board (the speakers don't pop when its turned on but they make that shhhhhhhh sound like the amp is on.but one of the two large power transisters on the driver board is heating up pretty good). 6 tuck n roll cabs 2=2x15, 2=2x15+horn,1 single 15, 1=2x12, I've got the K-4 Bass head, K-3 Lead head and 2 K-1501 tolex square PA roll cab's and a loaded cabinet I'm looking for a K-100 combo amp head to put in it. Yea I got some Kustom stuff STEVE

Steve C
Re: Schematics needed [message #11763 is a reply to message #11733] Sat, 05 September 2009 19:48 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4250
Registered: June 2004
Location: NY
Senior Member
I will scan them and email them to you on Tuesday, but the k100s are the same circuts but use one half of the out put stage of the k200 models. I am not sure the kasino PA, is that not just like the k100 pa? what does it have for board numbers?
Re: Schematics needed [message #11765 is a reply to message #11763] Sat, 05 September 2009 21:54 Go to previous message
cassent5150 is currently offline  cassent5150
Messages: 341
Registered: August 2009
Senior Member
Thanks, the PC Driver on the Kasino 100 is KE1 900 and pre amp is a KE1-1 PC803. Thanks again STEVE

Steve C
Previous Topic: Have Replacements Been Found Yet
Next Topic: K200B1 Head
Goto Forum:
  


Current Time: Sat Feb #d 22:24:12 EST 2020
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.