Home » VintageKustom.com » Replacement Part Suggestions » kustom head
kustom head [message #13545] Tue, 04 May 2010 07:50 Go to next message
Billyerock is currently offline  Billyerock
Messages: 12
Registered: January 2010
Location: Englewood colorado
Junior Member
I have a Kustom amp .. on the face side of the amp it says its a Bob Ross amp ... there isn't any model or serial number on the back ... nor is there a place where one was, no signs of one ever being there .. some sort of rivet hole ...or where it may have been glued on screw on it just isn't there

looking at the amp strait on the knobs read as followed

left side top knobs Right side top knobs
Rev, speed, Volume, bright vol bright slective boost har Clip
left side bottom knobs right side bottom knobs
tremolo inten bass treb bass treb boost volume clib volume

can anybody help me with the model number on this one

[Updated on: Tue, 04 May 2010 07:57]

Report message to a moderator

Re: kustom head [message #13546 is a reply to message #13545] Tue, 04 May 2010 08:20 Go to previous messageGo to next message
Dom Franco is currently offline  Dom Franco
Messages: 2
Registered: May 2010
Location: Beaverton, OR
Junior Member
I have that same amp model )))200((( on the front
it came with a blue jewel pilot light. I bought it in the 1970's
It works but very noisy. I have replaced a transistor in the preamp once before. I need a schematic and I am excited to dig in and fix my baby. Dom Franco


Dom Franco
Re: kustom head [message #13547 is a reply to message #13545] Tue, 04 May 2010 08:34 Go to previous messageGo to next message
pleat is currently offline  pleat
Messages: 1452
Registered: June 2004
Location: Belding, Mi
Senior Member
It sounds like it's a K200A-4 amp. There should be a XLR Jack on the lower right side looking at the back of the amp where the footswitch jack would plug in.

The early 200A series used a aluminum foil sticker on the upper left side on the back of the amp for model and serial number that could have been peeled off. Yours probably have round silver kitchen drawer knobs for the power cord wrap.

The K200B series would not have the By Ross under the power light. The )))200((( under the Kustom logo would be the B series and would have 1/4" footswitch jacks on models with effects.
pleat
Re: kustom head [message #13549 is a reply to message #13545] Tue, 04 May 2010 11:48 Go to previous messageGo to next message
rodak
Messages: 511
Registered: October 2001
Location: Georgia
Senior Member
Bob Ross? It's probably "Bud Ross". Or perhaps does it say "Kustom By Ross"?

Can you post a picture of it?


www.combo-organ.com
Re: kustom head [message #13558 is a reply to message #13546] Wed, 05 May 2010 06:21 Go to previous messageGo to next message
Billyerock is currently offline  Billyerock
Messages: 12
Registered: January 2010
Location: Englewood colorado
Junior Member
yes there is a XLR looking jack on it there is also a rca jack back there too ... and I have a foot switch

[Updated on: Wed, 05 May 2010 06:23]

Report message to a moderator

Re: kustom head [message #13559 is a reply to message #13549] Wed, 05 May 2010 06:27 Go to previous messageGo to next message
Billyerock is currently offline  Billyerock
Messages: 12
Registered: January 2010
Location: Englewood colorado
Junior Member
It says across the front panel of the amp Kustom ... below that it says By Bob Ros inc ...
Re: kustom head [message #13560 is a reply to message #13547] Wed, 05 May 2010 06:33 Go to previous messageGo to next message
Billyerock is currently offline  Billyerock
Messages: 12
Registered: January 2010
Location: Englewood colorado
Junior Member
yes it has the round silver knobs as the cord wrap... sounds like you've got it .... it must be the K200A-4 amp thanks for the info ... like all my amps I have a wiring diagram ... this one I don't ... can you help we where I can find one ...
Re: kustom head [message #13562 is a reply to message #13560] Wed, 05 May 2010 07:12 Go to previous messageGo to next message
pleat is currently offline  pleat
Messages: 1452
Registered: June 2004
Location: Belding, Mi
Senior Member
I don't have any schematics for your amp. I've never seen a kustom K200A series labeled anything but BY ROSS INC. Does your K200A have two white circuit breakers, one on each side of the power switch? The circuit breaker models used a etched aluminum face plate rather than the black plexi face control panels that were used on the Frankies and the latter K200A series without the circuit breaker models. Glad to hear you have the footswitch. The footswitch is a must if you want to use any of the effects. The cool thing with the A4 amp is all effects were routed to the left channel.
pleat
Re: kustom head [message #13688 is a reply to message #13559] Wed, 19 May 2010 07:59 Go to previous messageGo to next message
Billyerock is currently offline  Billyerock
Messages: 12
Registered: January 2010
Location: Englewood colorado
Junior Member
Correction it says, "By Ross INC"... my bad...
Re: kustom head [message #13711 is a reply to message #13688] Thu, 20 May 2010 21:56 Go to previous messageGo to next message
Shaun_Musings is currently offline  Shaun_Musings
Messages: 323
Registered: April 2009
Location: Reading, MA
Senior Member

Well, I have the same amp, and it sounds like an A4. There are some here who'll pay a pretty for that =)

SD


Born on the Baaaaayou (Ok, in Massachusetts)
Re: kustom head [message #14284 is a reply to message #13711] Sun, 05 September 2010 00:55 Go to previous message
wjhl18
Messages: 10
Registered: August 2010
Location: Cleveland
Junior Member
Do you still have the k210 cab for sale? can you send me a pic?

Jim London

440-686-0830
Thanks!
Previous Topic: Replacement transistor needed
Next Topic: Kustom 100 and 200 A's and B's
Goto Forum:
  


Current Time: Thu Mar #d 09:24:32 EDT 2024
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.