Home » VintageKustom.com » Replacement Part Suggestions » K200-B1 Replacement output transistors (necesito reemplazar los transistores de salida pero no tienen numero)
K200-B1 Replacement output transistors [message #20431] Sun, 06 April 2014 19:28 Go to next message
Eros Segovia is currently offline  Eros Segovia
Messages: 6
Registered: April 2014
Junior Member
Good Day ..
I'm from the north of mexico, I have an amplifier Kustom K200-B1.
the power is damage, check the output transistors and have no identification number to replace with new, as they mark 2 damage with multimeter in Ohms scale.
Can anyone help me if they have the numbers of transistors replacement?
they are greatly appreciate ..

Greetings.
Re: K200-B1 Replacement output transistors [message #20433 is a reply to message #20431] Sun, 06 April 2014 23:24 Go to previous messageGo to next message
chicagobill
Messages: 1934
Registered: April 2003
Senior Member
Welcome to the place. The original output transistors are selected 2N3055 types. Almost any high power NPN transistor will work in this circuit.

If you replace them, I would suggest that you go ahead and replace all four with the same type.
Re: K200-B1 Replacement output transistors [message #20434 is a reply to message #20433] Sun, 06 April 2014 23:43 Go to previous messageGo to next message
Eros Segovia is currently offline  Eros Segovia
Messages: 6
Registered: April 2014
Junior Member
Good Night ..
Thanks for helping me with the answer, but when I check with multimeter think they were PNP.
or if you have flat or electronic diagram to check for more components have to be replaced.
they are much appreciate.

My amp is K200 B-1.
and TO-3 transistors burned. Sunrise and have no part number for identification.

Greetings from Mexico ..
Re: K200-B1 Replacement output transistors [message #20436 is a reply to message #20431] Mon, 07 April 2014 06:39 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4212
Registered: June 2004
Location: NY
Senior Member
PNP type transistors can not be used in these amps without massivly reworking the driver circuit board on the rear wall of the amp.
Like Bill posted for you the transistors are 2N3055 which are NPN type.
I use NTE130 transistors for these most of the time.
Since the amp has been fitted with the wrong output transistors I would check all 4 of the box type 5 watt emitter resistors and I would also check all 4 of the boxed heatsinked driver transistors.

If you got look at the Technical to the left of the screen here we have the schematics you are asking about.
Re: K200-B1 Replacement output transistors [message #20439 is a reply to message #20436] Mon, 07 April 2014 15:52 Go to previous messageGo to next message
Eros Segovia is currently offline  Eros Segovia
Messages: 6
Registered: April 2014
Junior Member
Good afternoon compadres.

and I could see the diagrams on their website and which I am very grateful.
here in mexico if I can locate to replace damaged components.
My bass amp is a gem for my son and for me, since I eonido are strong and so crystal I fall from that phone to hear for the first time.

Greetings from Mexico.

a hug .. Surprised Surprised Surprised
Re: K200-B1 Replacement output transistors [message #20440 is a reply to message #20436] Mon, 07 April 2014 15:54 Go to previous messageGo to next message
Eros Segovia is currently offline  Eros Segovia
Messages: 6
Registered: April 2014
Junior Member
Good afternoon compadres.

and I could see the diagrams on their website and which I am very grateful.
here in mexico if I can locate to replace damaged components.
My bass amp is a gem for my son and me, are as strong and sound as crystal that I fall since I first heard.

Greetings from Mexico.

a hug ..
Re: K200-B1 Replacement output transistors [message #20446 is a reply to message #20431] Tue, 08 April 2014 06:48 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4212
Registered: June 2004
Location: NY
Senior Member
Hello again!
If you can not find the semiconductors you need to repair the amp in Mexico then the closest US supplyer to you would be Mouser electronics in Texas.
They stock NTE semiconductors.
The output transistors are NTE 130 like I posted before, but if you need more than two of them I would order NTE130MP which is a matched pair.
If you need 3 output transistors, order two matched pairs.
The orignal driver transistors in the heatsinked boxes(38737 and 38736) cross over to NTE129 and NTE128 respectivly.
These do not have the box heat sink anymore so you will need a slip on top hat type heat sink for each transistor.
Another good repplacement for the oringinal RCA output transistors would be Motorola MJ15050.
The amps 3 amp fuse is likly blown also and you will need to order one of those.

If you have never worked on electronics before I would get the amp repaired by a electronic repair tech and have him contack us if he has any questions.

[Updated on: Tue, 08 April 2014 07:00]

Report message to a moderator

Re: K200-B1 Replacement output transistors [message #20474 is a reply to message #20446] Sun, 13 April 2014 19:14 Go to previous message
Eros Segovia is currently offline  Eros Segovia
Messages: 6
Registered: April 2014
Junior Member
Thanks Compadre. Good Afternoon ..

I had the problem with the RCA 38737 transistor (Q705). was burned.
but I found the solution answers that tell me it's the NTE 129.

I could already find in electronics stores in northern mexico. the city is Torreon Coahuila, / Gomez Palacio Durango.
replacement transistor 2N 3055., which is not expensive. and this at great cost.

Thanks for the help. Compadres.

Greetings ...
Previous Topic: Equivalent Transistor
Next Topic: where to get upgraded mail filters & spl drivers 250 kustom
Goto Forum:
  


Current Time: Mon Oct #d 17:12:19 EDT 2019
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.