Home » VintageKustom.com » Replacement Part Suggestions » K200B-6 (Loud pop in speakers when amp is powered on)
K200B-6 [message #27505] Mon, 16 September 2019 11:08 Go to next message
aeroboy47 is currently offline  aeroboy47
Messages: 4
Registered: September 2019
Junior Member
Amp makes loud pop when powered on. Other than that it works fine. Have checked numerous voltages and all are good according to schematic. If anyone has had a similar problem corrected, I would love to hear about it.
Re: K200B-6 [message #27506 is a reply to message #27505] Tue, 17 September 2019 06:06 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4218
Registered: June 2004
Location: NY
Senior Member
Hello!
The number 1 main reason for the loud pop instead of the normal thump that the amp should make is due to the two big can type 4500 / 50 volt power supply rail filters needing to be replaced..
A secondary reason could be the many smaller electrolytic type caps on the other circuit boards that the amp has.

To nail down where the issue is coming from you can do this check out.

The blue wires from each front mounted PC board carry the audio signal to the amps rear wall mounted PC703 board.

If you cut open each blue wire one at a time and then power on the amp again to can then confirm if it's either of these two boards that are making the loud pop .

These wires can the easily be soldered back together and insulated.
Re: K200B-6 [message #27507 is a reply to message #27506] Tue, 17 September 2019 16:40 Go to previous messageGo to next message
aeroboy47 is currently offline  aeroboy47
Messages: 4
Registered: September 2019
Junior Member
Thanks. I will try your suggestion. I have also found that one of the output transistors has nearly the same resistance (12k/13k)between the base and emitter.
Re: K200B-6 [message #27508 is a reply to message #27505] Wed, 18 September 2019 06:37 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4218
Registered: June 2004
Location: NY
Senior Member
Well that may be leaking D.C. Voltage and making for that bang at power up.

For all of the well less then bucks that these 2N3055 output Transistors cost each to day I would get a pair of them like the NTE131MP and install a new one on each side of the amps thermal cut off switch that sits between them and see if that clears up the issue, as., there far cheaper then new computer grade main can filters !

This will help to keep the output stage balanced for lower distortion and low output hum levels.
Re: K200B-6 [message #27511 is a reply to message #27508] Wed, 18 September 2019 11:16 Go to previous messageGo to next message
aeroboy47 is currently offline  aeroboy47
Messages: 4
Registered: September 2019
Junior Member
I'm going to replace all four of these output transistors. Resistance readings are not exactly what I would expect from any of them. I'll let you know if this corrects the problem. Thanks for the input.
Re: K200B-6 [message #27512 is a reply to message #27505] Wed, 18 September 2019 12:01 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4218
Registered: June 2004
Location: NY
Senior Member
Are they all original RCA 36892 Transistors?
Re: K200B-6 [message #27513 is a reply to message #27512] Thu, 19 September 2019 13:25 Go to previous messageGo to next message
aeroboy47 is currently offline  aeroboy47
Messages: 4
Registered: September 2019
Junior Member
Yes, they are all the original ones
Re: K200B-6 [message #27515 is a reply to message #27505] Thu, 26 September 2019 16:08 Go to previous messageGo to next message
rodak
Messages: 446
Registered: October 2001
Location: Georgia
Senior Member
Do the 2N3055s need to be "matched" in any way, or is that non-critical?

www.combo-organ.com
Re: K200B-6 [message #27516 is a reply to message #27505] Fri, 27 September 2019 05:43 Go to previous message
stevem is currently offline  stevem
Messages: 4218
Registered: June 2004
Location: NY
Senior Member
Ideally they should all be matched pretty close as that will allow the lowest amount of D.C. Voltage offset ( hum at idle) and the highest level of clean output wattage before clipping/ distortion.
Previous Topic: Blue On Off Switch
Next Topic: 3055 vs 3771 power transistors
Goto Forum:
  


Current Time: Wed Oct #d 06:42:09 EDT 2019
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.