Home » VintageKustom.com » Comment Board » Model 4-12 L 70's cabinet
icon5.gif  Model 4-12 L 70's cabinet [message #8717] Wed, 04 July 2007 06:17 Go to next message
KUSTOMBASS is currently offline  KUSTOMBASS
Messages: 15
Registered: July 2007
Location: NL
Junior Member
Hey there! I've got a Kustom Kuestion.
Is it possible, without destroying the cabinet, to use a Kustom III bass head on a 4-12L speaker cabinet?
It's the III tolex head an a vinyl cabinet.
Well, that was my question.

Regads and keep up the good work!

Michel from Holland
Re: Model 4-12 L 70's cabinet [message #8721 is a reply to message #8717] Thu, 05 July 2007 08:09 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4733
Registered: June 2004
Location: NY
Senior Member
Do you mean that you want to play bass thru the 4-12 cab, or just will the amp work thru the cab?
Yes you can play limited bass thru the 4-12 cab for light rehearshing, but I would not do it with 5 string bass as that low B string will push those speaker cones to their limit.
That head will drive down to a 4 ohm load, and that cab is most likly 8 or 16 ohms so your OK there also.
Re: Model 4-12 L 70's cabinet [message #8738 is a reply to message #8717] Tue, 10 July 2007 13:13 Go to previous messageGo to next message
edforgothispassword is currently offline  edforgothispassword
Messages: 202
Registered: July 2004
Senior Member
the 4x12 cab came stock from the factory wired for 4 ohms so it could get that 250 head peak rating as high as possible...the cab is a bit "floppy" wired that way, I rewired mine to 16ohms and it sounds notably better.

The cab will likely have Jensons in it originally..may have some CTS..regardless, those are guitar drivers and you'll walk em right out of their baskets if you are looking to play bass through them.
also, note that the cab has slots on the back...the little chrome ports up front were more in keeping with the trademark cosmetics..yeah, you'll get some reflex air blowing out of there, but the cab is slotted on the back to give those guitar 12s some needed air as well...through some eminence deltas or gammas in there and you'll have a cool bass rig..careful on trying the heavier Kapa series? I think that's their high end...tons of wattage, but the frame rim is so thick that the kustom studs aren't long enough to go through and leave thread for the nuts to tighten.
I have run my 4x12 cab with my 65 fender showman head and love it at the 16ohm wiring. I have also stacked a marshall jcm900 on there and it screams..that cab has a great full ness, while still rataining some openess in the middle tone due to the slotting on the back.. its a very enjoyable cab..better than the typical marshall 4x12.
Re: Model 4-12 L 70's cabinet [message #8739 is a reply to message #8717] Wed, 11 July 2007 03:13 Go to previous messageGo to next message
KUSTOMBASS is currently offline  KUSTOMBASS
Messages: 15
Registered: July 2007
Location: NL
Junior Member
Thank for those replys! Ive asked a friend of mine (also a Kustom fan AND Kustom/Sunn/Ampeg collector Shocked ...) and he told me that those 4-12L cabs work pretty fine for bass, also with the matching Lead top. I can buy a Kustom III lead with 4-12L cabinet for a VERY reasonable price so i'm going to try it for bass.
The music i play is quite loud (vistit: juliemittens.nl).
I used to play with the '80's Kustom III bas with matching cabinet but i blew up the speaker and not long after that the top blew up (or something like that). I think there was something wrong with top so it blew up my speaker. I play really loud music but i never put my top over 6 or 7.
The sound of that top, man, it was SO warm and had a room-filling sound. I am looking for somebody to fix it if possible.
So. Well. See ya'll! Have a nice day!
Re: Model 4-12 L 70's cabinet [message #8742 is a reply to message #8717] Wed, 11 July 2007 06:36 Go to previous message
stevem is currently offline  stevem
Messages: 4733
Registered: June 2004
Location: NY
Senior Member
It should not be all that hard to fix.
Previous Topic: kustom weights
Next Topic: size of K250-3
Goto Forum:
  


Current Time: Sat Apr #d 13:48:16 EDT 2024
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.