Home » VintageKustom.com » Repairing Kustom Amps » Kustom PC 102 Organ (Need help locating some leads)
Kustom PC 102 Organ [message #25418] Sat, 13 August 2016 20:35 Go to next message
sunnhead is currently offline  sunnhead
Messages: 221
Registered: June 2010
Location: Minnesota
Senior Member

was doing some work on my kombo and the back fell and the power and audio leads got pulled out of the board. So anyone have a picture of a PC 102 board so I can get the wires in the right place! Thanks

-S
Re: Kustom PC 102 Organ [message #25420 is a reply to message #25418] Mon, 15 August 2016 06:57 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4728
Registered: June 2004
Location: NY
Senior Member
So your Red, Green and blue wires snapped off?
Re: Kustom PC 102 Organ [message #25421 is a reply to message #25418] Mon, 15 August 2016 10:12 Go to previous messageGo to next message
sunnhead is currently offline  sunnhead
Messages: 221
Registered: June 2010
Location: Minnesota
Senior Member

yeah its a black red and blue wire.
Re: Kustom PC 102 Organ [message #25422 is a reply to message #25418] Mon, 15 August 2016 11:21 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4728
Registered: June 2004
Location: NY
Senior Member

I will try to take a picture tonight abd post it for you.
Re: Kustom PC 102 Organ [message #25423 is a reply to message #25418] Tue, 16 August 2016 06:53 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4728
Registered: June 2004
Location: NY
Senior Member
Sorry , I forgot that I no longer have a A series amp to take a picture of that 102 board from!

If others here can not help out with a picture then if you post up a clear shot of yours I can tell you what goes where, or now may be a good time to get down the basics of reading a schematic for that board from our technical section?!
Re: Kustom PC 102 Organ [message #25424 is a reply to message #25423] Tue, 16 August 2016 09:41 Go to previous messageGo to next message
sunnhead is currently offline  sunnhead
Messages: 221
Registered: June 2010
Location: Minnesota
Senior Member

I have two A-4 amps, I dint think of opening up one and taking a look at it!

-S
Re: Kustom PC 102 Organ [message #25425 is a reply to message #25418] Tue, 16 August 2016 10:13 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4728
Registered: June 2004
Location: NY
Senior Member
That may not help much in regards to a picture as the boards are stacked in the A series heads as effects boards are added!
Re: Kustom PC 102 Organ [message #25426 is a reply to message #25425] Tue, 16 August 2016 11:22 Go to previous messageGo to next message
chicagobill
Messages: 2005
Registered: April 2003
Senior Member
Sunnhead- You can also post a photo of your board and we can figure out where the wires should go back on.
Re: Kustom PC 102 Organ [message #25431 is a reply to message #25426] Wed, 17 August 2016 15:08 Go to previous messageGo to next message
sunnhead is currently offline  sunnhead
Messages: 221
Registered: June 2010
Location: Minnesota
Senior Member

I cant post pictures on here, so here is a link...

http://www.49live.com/Kustom/102.jpg
http://www.49live.com/Kustom/1022.jpg
Re: Kustom PC 102 Organ [message #25432 is a reply to message #25418] Thu, 18 August 2016 00:08 Go to previous messageGo to next message
chicagobill
Messages: 2005
Registered: April 2003
Senior Member
Looking at your photos, here's what I could figure out. All of the wires go to the left side of the board. At the lower left there is a blue wire still connected that should go to the two input jacks.

The three wires that need to be connected are the black ground wire, the red power supply wire and the blue output wire that goes to the main chassis power amp.

The black ground wire goes to the top left of the board. There is a hole just to the left of the back of the volume pot. If you look at the copper side of the board, you will see the copper trace from that hole goes under the pot and connects to the metal pot case.

The next wire is the blue output wire. If you look at the board, there are two black plastic cased transistors along the left edge of the board. Just to the left of the top transistor is the hole for the output wire.

The last wire is the red power supply wire. Below the volume pot, there is a tall white capacitor. Directly below this cap there are two holes, one of which had a wire soldered in it. That is where the red wire goes.

If you need any more info, just ask.
Re: Kustom PC 102 Organ [message #25436 is a reply to message #25418] Thu, 18 August 2016 11:03 Go to previous messageGo to next message
sunnhead is currently offline  sunnhead
Messages: 221
Registered: June 2010
Location: Minnesota
Senior Member

I think that will do just fine! Ill solder them in! thanks for your help.
Re: Kustom PC 102 Organ [message #25440 is a reply to message #25418] Thu, 18 August 2016 21:38 Go to previous message
sunnhead is currently offline  sunnhead
Messages: 221
Registered: June 2010
Location: Minnesota
Senior Member

yep that did the trick its all happy and running like it should! Thanks for your help!!!
Previous Topic: K-150-8 4x10 combo repair
Next Topic: Replacement for a PET8002 transistor
Goto Forum:
  


Current Time: Thu Mar #d 14:32:45 EDT 2024
.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.