VintageKustom.com: Repairing Kustom Amps » K250-1 bass head

Home » VintageKustom.com » Repairing Kustom Amps » K250-1 bass head (module input & ohms)

Show: Today's Messages :: Show Polls :: Message Navigator

Return to the default flat view

Create a new topic

Submit Reply

Re: K250-1 bass head [message #25613 is a reply to message #25582]

Thu, 29 September 2016 17:31

Kustom_Bart is currently offline

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

Sorry, that I didn't get back to you sooner on this. The Altec cabs were for the plexi faced Kustoms so, no modules in them at all. just a single input on them and they were 8 ohm cabs with two 16ohm speakers. That's the difficult part with finding the correct altec's is finding Kustom stamped 16ohm 418's or you can recone them at 8 ohms each reasonable and make each cabinet 8 ohms and use 2 cabs to draw the head down to 4 ohms. I have reconed a bunch of them and it is simple, it just takes a few basic hand tools and a little bit of time, not much just simple instructions and you can buy the kits for 69.99 including everything, including the glue. The only thing that it doesn't come with is the aluminum voice coil cover and they sell them new as well, very cheap.

Report message to a moderator

Send a private message to this user

[Message index]

		K250-1 bass head By: oren hudson on Wed, 19 September 2012 00:31
		Re: K250-1 bass head By: Kustom_Bart on Wed, 19 September 2012 12:42
		Re: K250-1 bass head By: oren hudson on Wed, 19 September 2012 22:42
		Re: K250-1 bass head By: Kustom_Bart on Wed, 19 September 2012 23:45
		Re: K250-1 bass head By: oren hudson on Fri, 21 September 2012 00:37
		Re: K250-1 bass head By: stevem on Fri, 21 September 2012 07:29
		Re: K250-1 bass head By: Kustom_Bart on Fri, 21 September 2012 10:06
		Re: K250-1 bass head By: pleat on Fri, 21 September 2012 21:54
		Re: K250-1 bass head By: woodsey on Tue, 20 September 2016 00:12
		Re: K250-1 bass head By: stevem on Tue, 20 September 2016 05:53
		Re: K250-1 bass head By: woodsey on Tue, 20 September 2016 10:21
		Re: K250-1 bass head By: stevem on Wed, 21 September 2016 05:57
		Re: K250-1 bass head By: woodsey on Mon, 16 July 2018 10:49
		Re: K250-1 bass head By: woodsey on Wed, 21 September 2016 21:06
		Re: K250-1 bass head By: Kustom_Bart on Thu, 29 September 2016 17:31
		Re: K250-1 bass head By: woodsey on Fri, 30 September 2016 19:25
		Re: K250-1 bass head By: Kustom_Bart on Sat, 01 October 2016 13:14
		Re: K250-1 bass head By: woodsey on Sat, 01 October 2016 14:32
		Re: K250-1 bass head By: pleat on Sat, 01 October 2016 17:16
		Re: K250-1 bass head By: woodsey on Sun, 02 October 2016 11:21
		Re: K250-1 bass head By: IowaBoy on Mon, 08 October 2018 21:54

Previous Topic:	K 100 8
Next Topic:	Retaining nuts stuck

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

PDF

]

Current Time: Sat Apr #d 11:12:32 EDT 2024

.:: Contact :: Home ::.

Powered by: FUDforum 3.0.9.